Loading...
HomeMy WebLinkAboutSWG2026-00164 TANK ONLY - SWG Application / Design - 5/22/2026 MASON COUNTY 415 N 6TH STREET,SHELTON,WA 98584 SHELTON:360-427-9670,EXT 400 BELFAIR:360-275-4467,EXT 400 Public Health & Human Services ELMA:360-482-5269,EXT 400 FAX:360-427-7787 On-Site Sewage System Tank Only Permit: SWG2026-00164 APPLICANT Maples,Shane Phone: 3604638474 Address: 911 SE Arcadia Rd.SHELTON, WA 98584 OWNER BLAIR NANCY JANE Phone: Address: PO BOX 1097 HOODSPORT, WA 98548 SEPTIC INSTALLER SHANE MAPLES* Phone: 360-463-8474 Address: 911 SE Arcadia Road SHELTON,WA 98584 Site Address: 380 N DUCKABUSH DR EAST Primary Parcel Number: 422095000062 Permit Description: Replace septic tank Permit Submitted Date: 05/22/2026 Permit Issued Date: 06/01/2026 Issued By: Rhonda Thompson Current Permit Fees Paid: $275.00 (additional fees may be required upon installation of system). Permit Expiration Date: 06/01/2027 (based on date of inspection) Type of Work OSS Repair Components being Replaced: Septic Tank Only Surfacing Sewage? No Existing Failure? Yes Shoreline? No Horizontal Setbacks Met? Yes Number of Bedrooms: 2 Drinking Water Source: Public Water System Additional Details: IM-1060 Permit Conditions: 2 Horizontal setbacks per WAC246-272A-0210 must be maintained, unless prior approval is obtained 5 Proposed development subject to zoning requirements and approval by the planning department staff per Mason County Title 17. 4 Mason County Asbuilt Form, Record Drawing, and Installation fee must be submitted for final installation approval. I Approval of this septic permit does not approve the building location. Building location is subject to approval from all applicable departments and regulations. 3 Permit must be installed by a Mason County Certified Installer unless prior written authorization from Mason County is obtained. THIS PERMIT MUST BE ONSITE DURING INSTALLATION OF OSS. PROPERTY OWNERS ARE RESPONSIBLE FOR DETERMINING AND MARKING ALL PROPERTY LINE AND EASEMENT LOCATIONS. THIS PERMIT MAY BE REVOKED IF THE SITE CONDITIONS HAVE CHANGED SINCE THE SITE WAS INSPECTED AND/OR DESIGN APPROVED. FINAL INSTALLATION APPROVAL IS REQUIRED PRIOR TO TEMPORARY OR FINAL OCCUPANCY OF ANY RELATED STRUCTURES. For Final Inspection visit: masoncountywa.gov/health/environmental/onsiteloss-inspection-request.php or call: 360-427-9670, extension 400. 9'ZZo'1- SO-o006Z ckX - I RECORD DRAWING (continued) I - $oj ccc�. 6U5h !r E I � f I a � I APPROVED JUN 012026 MASON COUNTY ENVIRONMENTAL HEALTH hoe RET 0 new (1760 (n(`'IFrhFar se - - 4vA✓'K j N �jo•tlLl (.A.1 iCf✓1 t`3' r ' ilk, 0 0 _ _ _ I �� ?j 1' Ccr+e 5eQ��v 4-,--r, 'C. )rINFILTRATORO tanks Features & Benefits • Strong injection molded U..^ polypropylene construction • Lightweight plastic construction and inboard lifting lugs allow for easy delivery and handling Integral heavy-duty green lids that interconnect with TWTM risers and pipe riser solutions Structurally reinforced access ports eliminate distortion during installation and pump-outs • Reinforced structural ribbing and fiberglass bulkheads offer additional strength • Can be installed with 6"to 48" of cover The Infiltrator IM-1 060 is a lightweight strong and durable septic tank. • Can be pumped dry during This watertight tank design is offered with Infiltrator's line of custom-fit pump-outs risers and heavy-duty lids. Infiltrator injection molded tanks provide a • Suitable for use as a septic tank, revolutionary improvement in plastic septic tank design, offering long-term pump tank, or rainwater exceptional strength and watertightness. (non-potable)tank Inlet Side • No special installation, backfill or Infiltrator water filling procedures are required TANK CUTAWAY Tw Riser System_ HEAVY DUTY LID CUTAWAY Reinforced 24" structural Partition access port _ _ __ I1 baffle wal\ ry Structural Ff T��: bulkheads �MID-SEAMA4UTAWJ� Z6 Reinforced water tight mid s ��� rpr�N ENTAL UA gasketed connection RET p. -.- E ii• Protecting the Environment with Innovative Wastewater Treatment Solutions INFILTRATOR® water technologies I IM-1060 General Specifications and Illustrations LIFTING STRAP LIFTING LUG RISER CONNECTION (TYPICAL) (4TOTAU (TYPICAL) The IM-1060 is an injection molded two piece mid-seam plastic tank.The IM-1060 injection molded plastic design A A allows for a mid-seam joint that has precise dimensions 0 0 for accepting an engineered EPDM gasket. Infiltrator's gasket design utilizes technology from the water industry °o °Q [1580] EXTERIOR to deliver proven means of maintaining a watertight seal. WIDTH The two-piece design is permanently fastened using a series of non-corrosive plastic alignment dowels and locking seam clips. The IM-1060 is assembled and sold through a network of certified Infiltrator distributors. 127.0[3226]ExTERIQR LENGTH TOP VIEW [,[ OUTLET Working Capacity 1094 gal(4141 L) Total Capacity 1287 gal(4872 L) C 54.7 Airspace 16.5% [1389] EXTERIOR HEIGHT SEAM CLIP Length 127"(3226 mm) (TYPICAL) Width 62.2"(1580 mm) LIFTING STRAP Length-to-Width Ratio 2.3 to 1 (TYPICAL) Height 54.7"(1389 mm) END VIEW Liquid Level 44"(1118 mm) Invert Drop 3"(76 mm) 04[1021 024[610]ACCESS OPENINGS WITH LOCKING LIDS(2) PVC OR ABS 0 4[102]PVC OR Fiberglass Supports 2 INLETTEE 10.2[260]FREEBOARD ABS OUTLETTEE Compartments 1 0r2 INLET 16.5% AIRSPACE OUTLET Maximum Burial Depth 48"(1219 mm) PER 30--I PER CT! CODE Minimum Burial Depth 6"(152 mm) 44.0 .1_ FIBERGLASS [11181 FIBERGLASS Maximum Pipe Diameter 6"(152 mm) SUPPORT LIQUID SUPPORT (TYPICAL) DEPTH (TYPICAL) WITH Weight 320 lbs(145 kg) WALLWHERE BAFFLE REQUIRED SIDE VIEW A1 TANKTOP / CONTINUOUS P P O V HALF GASKET JUN 012026 TANK � RIOR / � SEAM CLIP MASON COUNTY ENVIRONMENTAL HEAriff RE I DOWELALIGNMENT TANK BOTTOM 4 Business Park Road HALF P.O.Box 768 Old Saybrook,CT 06475 INFILTRATOR® 860-577-7000-Fax 860-577-7001 MID-HEIGHT SEAM SECTION 1-800-221-4436 water technologies www.infiltratorswater.com U.S.Patents:4,759,661;5,017,041;5,156,488;5,336,017;5,401,116;5,401,459;5,511,903;5,716,163;5,588,778;5,839,844 Canadian Patents:1,329,959;2,004,564 Other patents pending.Infiltrator,Equalizer, Quick4,and Sidewinder are registered trademarks of Infiltrator Water Technologies.Infiltrator is a registered trademark in France.Infiltrator Water Technologies is a registered trademark in Mexico. Contour,MicroLeaching,PolyTuff,Chamberspacer,Mult]Port,PosiLock,QuickCut,QuickPlay,SnapLock and StraightLock are trademarks of Infiltrator Water Technologies. PolyLok is a trademark of PolyLok,Inc.TUF-TITE is a registered trademark of TUF-TITE,INC.Ultra-Rib is a trademark of IPE(Inc. ©2013 Infiltrator Water Technologies,LLC.All rights reserved.Printed in U.S.A. IM02 1213