Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
BLD2017-00651 SFR - BLD Permit / Conditions - 9/13/2017
Inspection Line(360)427-7262 � UkrA. MASON COUNTY DEPT. OF COMMUNITY DEVELOPMENT Phone: (360)427-9670, ext. 352 �- Mason County 615 W Alder St _ Shelton, WA 98584 S° RESIDENTIAL BUILDING PERMIT BLD2017-00651 OWNER: CEDARLAND FOREST RESOURCES CONTRACTOR: LICENSE: EXP: RECEIVED: 7/7/2017 SITE ADDRESS: 111 E WESTLAKE WAY ALLYN ISSUED: 9/13/2017EXPIRES: 3/13/2018 PARCEL NUMBER: 122195000034 LEGAL DESCRIPTION: LAKELAND VILLAGE 7 LOT: 34 PROJECT DESCRIPTION: DIRECTIONS TO SITE: NEW SFR: 1570 sq ft W/ATTACHED GARAGE General Information Construction &Occupancy Information Square Footage Information No. of Bedrooms: 3 Type of Constr.: VB Type of Use: SF Insp. Area: No. of Bathrooms: 2 Occ. Group: R3 Lot Size: Deck: 314 Type of Work: NEW Fire Dist.: 5 No. of Stories: Occ. Load: Building:1,570 Garage-Attached 560 Valuation: $ 201,853.30 Building Height: Occ. Status: Primary Basement: Manufactured Home Information Setback Information Shoreline& Planning Information Make: Length: Ft. Front: E 25.0 Ft. Shoreline: Ft. Water Body: Rear: Ft. Slope: Ft. SEPA?: Unkn Model: Width: Ft. Side 1:SW 5.0 Ft. Shoreline Desig.: hWtiApplicable Year: Serial No.: Side 2:NW 5.0 Ft. Comp. Plan Desig.: Urban Growth Area Plumbing Fixtures Mechanical Fixtures FEES Type Qty. Type Qty. Type By Date Amount Receipt Water Closets (Toilets) 2 Furnace<100K 1 Plan Check Fee JBN 7/7/2017 $ 1,017.22 S220170000000( Lavatories 3 Ventilation Fan 3 EH Plan Review JBN 7/7/2017 $210.00 S220170000000( Bath Tubs 2 Propane Tank 1 Planning Review Fee JBN 7/7/2017 $205.00 S220170000000( Showers 2 Gas Outlets 3 Building State Fee MPB 9/11/2017 $4.50 S320170000000( Water Heaters 1 Exhaust Hood 1 Mechanical Permit Fee MPB 9/11/2017 $ 146.70 S320170000000( Clothes Washer 1 Dryer Vent 1 Mechanical Base Fee MPB 9/11/2017 $28.50 S320170000000( Kitchen Sink, w/disposal 1 Plumbing Permit Fee MPB 9/11/2017 $ 119.30 S320170000000( Dishwasher 1 Plumbing Base Fee MPB 9/11/2017 $24.70 S320170000000( Hosebibs 2 Building Permit Fee MPB 9/12/2017 $ 1,564.95 S320170000000( Total $3,320.87 BLD2017-00651 Please refer to the following pages for conditions of this permit. Page 1 of 8 CASE NOTES FOR BLD2017-00651 CONDITIONS FOR BLD2017-00651 1) Prior to final approval, all upland areas disturbed or ne I cr ated by construction activities shall be seeded, vegetated or given an equivalent type of erosion protection (silt fencing or straw matting). X 2) Approv9d ner dimensions and setbacks on submitted site plan. Setbacks are measured from the furthest projection of the structure. X 3) Applica io acknowledges that the structure is only permitted for a use consistent with the current zoning of the parcel. Zoning is Allyn UGA- R-1 P. X 4) Contractor registration laws are governed under RCW 18.27 and enforced by the WA State Dept of Labor and Industries, Contractor Compliance Division. There are potential risks and monetary liabilities to the homeowner for using an unregistered contractor. Further information can be obtained at 1-80OM710y982. The person signing this condition is either the homeowner, agent for the owner or a registered contractor according to WA state law. X V` 5) All approved plans are required to be on-site for inspection purposes. If an inspection is called for and plans are not available on site, then approval will not be rant ed. In addition, a re-inspection fee (refer to current fee schedule, minimum 1 hour)will be charged and must be collected by the Building Depa n for to any further inspections being performed or approvals granted. X 6) Owner/ e t is r onsible to post the assigned address and/or purchase and post private road signs in accordance with Mason County Title 14.28. X 7) The plan review check list and corrections are part of the approved plans and must remain thereto. It is the responsibility of the applicant to make the corrections indicated on the plans. Once the plans are marked "APPROVED", they shall not be changed or altered without authorization from the Building Official. The permit holder is responsible to retain the complete approved set of plans on site for the duration of the project. Failure to comply and/or remov I f proved documents will result in failure of required building inspections. X 8) THE&IJ�VDATION SYSTEM SHALL BE PLACED ON UNDISTURBED, FIRM-NATIVE SOIL. X ��--�� 9) The "approved" site plan is required to be on-site for inspection purposes. If an inspection is requested and the "approved" site plan is not on site, then approval will not be granted. In addition, a re-inspection fee (refer to current fee schedule, minimum 1 hour)will be charged and shall be collected by the Buildin a artm prior to any further inspections being performed or approvals granted. X BLD2017-00651 Please refer to the following pages for conditions of this permit. Page 2 of 8 10) Adopted IECC/Washington State Energy Code Compliance has been approved as follows: Heat Type: Electric or other than electric, Compliance Method: Prescriptive option Marine-4C, Window(Max U-Factor):0.30, Skylight(Max U-Factor):0.50, Doors (Type/Max U-Factor):0.30 or less, Wall insulation R-21, Floor insulation R-30, Ceiling Insulation min. R-49, Vault Insulation R-38, and Slab Insulation R-10. In addition the following credits from WSEC table R406.2 shall be completed as follows: 1A: EFFICIENT BUILDING ENVELOPE Prescriptive compliance is based on Table R402.1.1 with the following modifications: Vertical fenestration U = 0.28 Floor R-38 Slab on grade R-10 perimeter and under entire slab Below grade slab R-10 perimeter and under entire slab or Compliance based on Section R402.1.4: Reduce the Total UA by 5%. 3A: HIGH EFFICIENCY HVAC EQUIPMENT Gas, propane or oil-fired furnace with minimum AFUE of 94%, or Gas, propane or oiled-fired boiler with minimum AFUE of 92% 5A: EFFICIENT WATER HEATING All showerhead and kitchen sink faucets installed in the house shall be rated at 1.75 GPM or less. All other lavatory faucets shall be rated at 1.0 GPM or less. 5C: EFFICIENT WATER HEATING Water heating system shall include one of the following: Gas, propane or oil water heater with a minimum EF of 0.91 or Solar water heating supplementing a minimum standard water heater. Solar water heating will provide a rated minimum savings of 85 therms or 2000 kWh based on the Solar Rating and Certification Corporation (SRCC)Annual Performance of OG-300 Certified Solar Water Heating Systems or Electric heat pump water heater with a minimum EF of 2.0 and meeting the standards of NEEA's Northern Climate Specifications for Heat Pump Water Heaters X BLD2017-00651 Please refer to the following pages for conditions of this permit. Page 3 of 8 11) A permanent certificate, completed by the owner, builder or registered design professional, shall be posted within three feet of the electrical distribution panel. The certificate shall list the predominant R-values of insulation installed in or on ceiling/roof, walls, foundation (slab, basement wall, crawlspace wall and/or floor), and ducts outside the conditioned spaces; U-factors for fenestration; and the solar heat gain coefficient (SHGC) of fenestration. Where there is more than one value for each component, the certificate shall list the value covering the largest area. The certificate shall list the type and efficiency of heating, cooling, and service water heating equipment, duct leakage rates including test conditions as specified in WSEC Section 105.4, and air leakage results if a blower door test was conducted. Building envelope air leakage control shall be considered acceptable when tested to have an air leakage less than 5 air changes per hour when tested with a blower door in accordanve with IECC/.WSEC Section R402.4. The blower door test results shall be recorded on the permanent certificate required located near the electrical distribution panel. Air leakage testing is not required for additions less than 750 square feet. Reference IECC/WSEC R401.3. Compliance certificates are available online at the WSU Energy program website titled, " WSEC 2015 Certificate" and are available in %or Y sheets. The Mason aE7 it Center will also have some available. X 12) A minimum of 75 percent of all permanently installed lamps in lighting fixtures shall be high efficacy lamps in accordance with IECC/WSEC Section R404.1. X b�1 13) WIND LOADS - Roof coverings shall be designed and tested to withstand the maximum basic wind speed. The basic wind speed for Mason County is 85 MPH. X 14) REQUIREMENTS FOR ROOF COVERINGS. Roof coverings shall be applied in accordance with the applicable provisions of the current code and the manufacturer's installation instructions. A drip ed shall be provided at eaves and gables of shingle roofs. (IRC 2012 R905.2.8.5) X 15) A Mason County Stormwater Management Worksheet was completed and signed as part of this building permit application. Design, sizing, placement, inspection and maintenance of stormwater management systems shall be the responsibility of the owner/agent of the developed parcel. It is the owner/agent/contractor's responsibility to ensure that Mason County Department of Public Works has approved the stormwater site plan for this parcel prior to the commencement of any development activities. *NOTE if Stormwater Management option "A"was selected on the Small Parcel Stormwater Management Application/Worksheet the document entitled "Managing Storm Drainage on Small Lots, The Small Parcel Stormwater Site Plan" constitutes an approved plan based on the criteria listed on the application/worksheet. If the development has, or will have, a septic/drainfield system you are responsible for contacting Mason County Division of Environmental Health to ensure that the stormwater system will not adversely affect the septic system of this, or any other, parcel. You may also wi h to consult with the septic design professional involved with the project. By calling for a final inspection of the building permit the owner/agent/contrac r knowledging that all components of the stormwater management system have been installed as approved on the stormwater site plan. X BLD2017-00651 Please refer to the following pages for conditions of this permit. Page 4 of 8 16) A concrete encased grounding electrode must be installed and used at each new building or structure that is built upon a permanent concrete foundation. In Mason County the electrical code is regulated by Washington State Department of Labor& Industries (L&I). For more information contact L&I for additional information. In Olympia call (360)902-6350 and in Bremerton call (360)415-4000. X a�� — 17) Owner/builder assumes all responsibility if drainfield/reserve area is encumbered. A. Drainfield/ Reserve requires a 10ft setback from all footing/foundations. B. Septic tank(s) requires 5ft setback from all footing/foundations. C. I undation drains within 30ft, down gradient of drainfield/reserve area. X 18) A separate inspection in addition to the inspections required in the IBC, Section 110 shall be required in accordance with the 2015 IBC, Section 1705.12.2 and Section 1707.1. The additional inspection is required when shear wall fastener spacing is required to be 4 inches or less. The shear wall schedule shown on sheet L1 and D1 designate wall type Portal Frame with fastener spacing 4 inches or less. The required inspection may be performed by the Mason County Building Department, a WABO certified inspector, certified to inspect lateral connections, the Engineer of record (EOR), or an authorized representative of the (EOR). The special inspectors duties and responsibilities shall be as specified in Chapter 17. When a third party inspector is used to perform the inspection, special inspection reports shall be submitted to the Mason County Building Department, 615 W Alder St, Shelton, WA 98584 and also available on site for review by the Building Official. Inspection reports shall be completed and sub m ted to the Mason County Building Department in a timely manner and shall be submitted prior to the framing inspection of said project. X 19) Carbon monoxide alarms, listed as complying with UL 2075 shall be installed in accordance with manufacturer specifications and in accordance with IRC Section R315. Alarms shall be installed outside of each separate sleeping area in the immediate vicinity of the bedrooms and on each level of the dwelling. EXISTING DWELLINGS shall be equipped with carbon monoxide alarms when alterations (including addition or alteration of fuel burning appliances), repairs r a ditions requiring a permit occur, or when one or more sleeping rooms are added or created. X 20) Any changes in proposed construction shall be reviewed by the engineer or architect of record and submitted in writing to the Mason County Building Department prior to construction. All engineering and/or architectural documents are a part of the approved set of plans and shall remain attached thereto. If documents are removed, approval will not be granted. In addition, a re-inspection fee (refer to current fee schedule, minimum 1 hour)will be charge�n shall be collected by the Building Department prior to any further inspections being performed or approvals granted. X 21) All construction must meet or exceed all local ordinances and the international codes requirements as adopted and amended by Mason County and the State of shington. Occupancy is limited to the approved and permitted classification. Any non-approved change of use or occupancy would result in permit r v ion. X BLD2017-00651 Please refer to the following pages for conditions of this permit. Page 5 of 8 22) Installation of heating equipment in a single-family residence shall meet the requirements of the current IECC/WSEC R403, applicable sections of the IRC, and IMC. Heating equipment shall be sized in accordance to ICC/WSEC, Section R403.6. Heating and design load calculations for the purpose of sizing HVAC systems are required and shall be calculated in accordance with accepted practice, including infiltration and ventilation. Design calculations shall be available for inspection during inspection. Referencing IRC M1601.4, all ducts, air handlers, filter boxes, and building cavities shall be sealed. All joints of duct systems and seams shall be made substantially air tight by means of tapes, mastics, liquid sealants, gasketing or other approved closure systems. Closure systems used with rigid fibrous glass ducts shall comply with UL181A and shall be marked 181A-P for pressure-sensitive tape, 181A-M for mastic or 181 A-H for heat-sensitive tape. Closure systems used with flexible air ducts and flexible air connectors shall comply with UL181 B and shall be marked 181 B-FX for pressure-sensitive tape or 181 B-M for mastic. Duct connections to flanges of air distribution system equipment or sheet metal fittings shall be mechanically fastened. Mechanical fasteners for use with flexible nonmetallic air ducts shall comply with UL 181 B and shall be marked 181 B-C. Crimp joints for round metal ducts shall have a contact lap of at least 1-1/2 inches (38 mm) and shall be mechanically fastened by means of at least three sheet-metal screws or rivets equally spaced around the joint. Closure systems used to seal metal ductwork shall be installed in accordance with the manufacturer's installation instructions. Duct tape is NOT permitted as a sealant on any ducts. When ducts are located in unheated spaces the ducts hall be insulated to R-8 DUCT TIGHTNESS TESTING shall be conducted by person(s) trained to perform such testing. A signed affidavit documenting test results in accordance to IECC/WSEC Section R403.3.3 shall be provided to the Mason County Building Department prior to the final occupancy inspection. Affidavit forms are available on at the WSU-Energy Program website titles, "Duct Leakage Affidavit" or"Duct Leakage Testing Results (Existing Construction)." Duct tightness testing is not required if the air handler and all ducts are located within the heated space. X 0 23) The demolition and disposal of debris must meet the regulations of Mason County and Olympic Region Clean Air Agency(ORCAA). It is unlawful for any person to cause or allow the demolition (or major renovation) of any structure unless all asbestos containing materials have been identified and removed from the area to be demolished. Work shall not commence on an asbestos project or demolition project unless the owner or ope tor has obtained written approval from ORCCA.2490 B Limited Lane NW, Olympia WA 98502, 360.586.1044/800.422.5623 www.orcaa.org X 24) Proposed structure or portions thereof, nt ark intain a 5' separation distance between adjacent structures. Separation is measured from furthest projection to furthest projection. X V_/ 25) All changes to"approved" building plans that effect compliance with the international codes as amended and adopted, or any other Mason County ordf nqp or regulation, must be reviewed and approved by Mason County prior to construction. X BLD2017-00651 Please refer to the following pages for conditions of this permit. Page 6 of 8 26) CONSTRUCTION PROCESS TO BE FIELD CORRECTED AS REQUIRED PER MASON COUNTY BUILDING DEPARTMENT AND THE ADOPTED BUILDING CODE. The construction of the permitted project is subject to inspections by the Mason County Building Department. All construction must be in conformance with the international codes as amended and adopted by Mason County. Any corrections, changes or alterations required by a Mason County Building Inspe s II be made prior to requesting additional inspections. X ft 27) All propane tanks must be installed in accordance with the International Fire Code and all applicable Mason County ordinances. All propane tanks filled on site must be located a minimum of 10' from any possible source of ignition (electrical outlets, electrical fixtures, compressors, etc), mechanical system air intake (direct vent appliance, ventilation air intake, etc), and/or any weeds, grass, brush, trash or any other similar combustible materials. Propane tanks less than 125 gallons must also be located a minimum of 5'from any building opening (foundation vents, windows, doors etc). Setback to the public way, or access easements shall be the greater of 25-ft or as specified in the Mason County Development Regulations. Setback to property lines shall be the grater of 5-ft or as specified in the Mason County Development Regulations. If a propane tank is exposed to probable vehicular damage, protective bolls st be installed. X e 28) All propane tanks must be installed in accordance with the International Fire Code and all applicable Mason County ordinances. All Propane tanks between 125 and 500 gallons must be located a minimum of 10' from any building, possible source of ignition (electrical outlets, electrical fixtures, compressors, etc), and/or any weeds, grass, brush, trash or any other similar combustible materials. Setback to the public way, or access easements shall be the greater of 25-ft or as specified in the Mason County Development Regulations. Setback to property lines shall be the greater of 10-ft or as specified in the Mason County Development Regulations. If a propane tank is exposed to probable vehicular damage, protective bollards must be inst d. X o 29) All pr ane tanks must be installed in accordance with the International Fire Code and all applicable Mason County ordinances. All propane tanks must meet n requirements and minimum setbacks as listed in the Mason County Fire Marshal's Standards for the Installation of Propane Tanks. X tki s Ilatio 30) Fuel piping shall be inspected after the installation of fuel piping is complete, and before the attachment of fixtures, appliances, or shut-off valves. At the time o spection the test pressure shall be no less than 10 psi held for no less than 15 minutes. Appliances to be attached to the fuel piping system shall not b e ntil t final inspection has been performed and approved by a Mason County building inspector. X 31) Owner/applicant must obtain a seperate for the placement of any size propane tank serving a fixed appliance within a dwelling structure or unit prior to the placement of the tank. X . qyl_ 32) The placement of small propane tanks are not normally subject to a permit review by the Planning Department; however, propane tanks are subject to Planning Department regulations. Such regulations primarily consist of setbacks from shorelines and features considered to be critical areas (streams, wetlands, slopes, etc.) If you think such features exist on or nearby your property, please contact the Planning Department so that exact setback requirements can be determined. X os___ 33) All pr erty lines shall be clearly identified at the time of foundation inspection. X BLD2017-00651 Please refer to the following pages for conditions of this permit. Page 7 of 8 34) All building permits shall have a final inspection performed and approved by the Mason County Building Department prior to permit expiration. The failure to request a final inspection or to obtain approval will be documented in the legal property records on file with Mason County as being non-compliant with Masy y ordinances and building regulations. X 35) All permits expire 180 days after permit issuance, or 180 days after the last inspection activity is performed. The Building Official may extend the time for actin for a period not exceeding 180 days, upon the receipt of a written extension request indicating that circumstances beyond the control of the permit hold r prevented action from being taken. No more than one extension may be granted. X 36) Pres re treated wood manufactured after January 1, 2004 may contain high concentrations of copper which could quickly corrode metal fasteners, con t r , and flashing. Install metal connectors approved for contact with the new types of pressure treated material. X 37) Landings and stairs must meet the same setback conditions as any permitted structure; and, must be shown on your site plan. Please check your 'Ap r ve Site Plan"to ensure these structures are shown and meet the setback conditions listed. X OWNER/ BUILDER acknowledges submission of inaccurate information may result in a stop work order or permit revocation. Acknowledgement of such is by signature below. I declare that I am the owner, owners legal representative, or contractor. I further declare that I am entitled to receive this permit and to do the work as proposed. I have obtained permission from all the necessary parties, including any easement holder or parties of interest regarding this project. The owner or authorized agent represents that the information provided is accurate and grants employees of Mason County access to the above described property and structure(s) for review and inspection. This permit/application becomes null &void if work or authorized construction is not commenced within 180 days or if construction work is suspended for a period of 180 days. PROOF OF CONTINUATION OF WORK IS BY MEANS OF INSPECTION. INACTIVITY OF THIS P IT APPLICATION OF 180 DAYS WILL INVALIDATE THE APPLICATION. Sign ure 1, Date OWNER - REPRESENTATIVE - CONTRACTOR Print Name (Circle one to indicate) - -- BLD2017-00651 Please refer to the following pages for conditions of this permit. Page 8 of 8 f WSEC/Ventilation Code Compliance Application Submit with heating/cooling system size worksheet (see instructions #4) Owner: Parcel#: Type of project: i Total Sq. Ft. 1st Floor: 2"d floo : Heate Basement: of heated area:: 1,5-70J Heating System Type: O Electric wall heater O Electric Central Furnace LPG Furnace O Heat Pump with electric furnace O Heat pump with gas furnace O Ductless 4t Pump O Boiler, specify fuel type: O Other: Specify: Prescriptive Option Table R402.1.1 (see table on previous page) Compliance Method Component Performance, R402.1.3 — Calculation worksheets required Must Check one:: ❑ Other (Specify): Check one ❑ Whole House Ventilation system Whole House Ventilation Ventilation using exhaust fans&window or wall Ztegrated with a Forced Air ❑ Other, describe: fresh air vents (M1507.3.4). If using System (M1507.3.5) System window vents be sure to order windows with vents. Referencing Table R406.2, "Additional Residential Energy Efficiency Requirements," all residential units must develop credits as specified in Table 406.2. Identify and describe which option(s)will be used to comply. If the table is not attached to this form you can access the table on our website at: http://www.co.mason.wa.us/forms/Community Dev/iecc wsec.pdf a) Description: Small dwelling units: less than 1,500 sq. feet of heated or cooled floor Additional area and less than 300 sq. ft fenestration area (skylights, doors, windows, etc). Energy "Including additions to existing building that are greater than 500 sq. ft. of heated floor Efficiency but less than 1,500 sq ft of floor area. Requires 1.5 credits Requirements b) Medium dwelling units that are not included in (a) above {small dwelling), OR (c) below Energy credits {large dwelling) Requires 3.5 credits required: EXCEPTION: Dwelling units serving R-2 occupancies shall require. Requires 2.5 3,5 credits. See page two for description. c) Large dwelling unit is a dwelling unit that exceeds 5,000 sq. ft. of heated or cooled floor area. Requires 4.5 credits d) Additions less than 500 sq feet. Requires .5 credits (Fenestration is defined in the IECC as skylights, roof windows, vertical windows, opaque doors, glazed-doors that include products with glass and non-glass glazing materials. Describe Energy Credit Option(s): r 0 RlE Tl JCS G Using Option number(s): � j r, i� ( � ice► `fir E—AC--LDFF— lqy �-A —42 —% I cel,�L"J EFF I C iC-VT VATER REATW& 3 Energy Credits (2015 WSEC - Table 406.2) OP DESCRIPTION CREDIT(S) a EFFICIENT BUILDING ENVELOPE la: 0.5 Prescriptive compliance is based on Table R402.1.1 with the following modifications: Vertical fenestration U =0.28 Floor R-38 Slab on grade R-10 perimeter and under entire slab Below grade slab R-10 perimeter and under entire slab or Com fiance based on Section R402.1.4: Reduce the Total UA by 5%. 1 b EFFICIENT BUILDING ENVELOPE lb: 1.0 Prescriptive compliance is based on Table R402.1.1 with the following modifications: Vertical fenestration U =0.25 Wall R-21 plus R-4 Floor R-38 Basement wall R-21 int plus R-5 ci Slab on grade R-10 perimeter and under entire slab Below grade slab R-10 perimeter and under entire slab or Compliance based on Section R402.1.4: Reduce the Total UA by 15%. EFFICIENT BUILDING ENVELOPE 1c: 2.0 Prescriptive compliance is based on Table R402.1.1 with the following modifications: Vertical fenestration U =0.22 Ceiling and single-rafter or joist-vaulted R-49 advanced Wood frame wall R-21 int plus R-12 ci Floor R-38 Basement wall R-21 int plus R-12 ci Slab on grade R-10 perimeter and under entire slab Below grade slab R-10 perimeter and under entire slab or Compliance based on Section R402.1.4: Reduce the Total UA by 30%. EFFICIENT BUILDING ENVELOPE 1d: 0.5 Prescriptive compliance is based on Table R402.1.1 with the following modifications: Vertical fenestration U=0.24 2a AIR LEAKAGE CONTROL AND EFFICIENT VENTILATION 2a: 0.5 Compliance based on R402.4.1.2: Reduce the tested air leakage to 3.0 air changes per hour maximum and All whole house ventilation requirements as determined by Section M 1507.3 of the International Residential Code shall be met with a high efficiency fan(maximum 0.35 watts/cfin),not interlocked with the furnace fan.Ventilation systems using a furnace including an ECM motor are allowed,provided that they are controlled to operate at low speed in ventilation only mode. To qualify to claim this credit,the building permit drawings shall specify the option being selected and shall specify the maximum tested building air leakage and shall show the qualiPiing ventilation system. 2b AIR LEAKAGE CONTROL AND EFFICIENT VENTILATION 2b: 1.0 Compliance based on Section R402.4.1.2: Reduce the tested air leakage to 2.0 air changes per hour maximum and All whole house ventilation requirements as determined by Section M1507.3 of the International Residential Code shall be met with a heat recovery ventilation system with minimum sensible heat recovery efficiency of 0.70. To qualify to claim this credit,the building permit drawings shall specify the option being selected and shall specify the maximum tested building air leakage and shall show the heat recovery ventilation system. 5 OPTION DESCRIPTION CREDIT(S) 2c AIR LEAKAGE CONTROL AND EFFICIENT VENTILATION 2c: 1.5 Compliance based on Section R402.4.1.2: Reduce the tested air leakage to 1.5 air changes per hour maximum and All whole house ventilation requirements as determined by Section M 1507.3 of the International Residential Code shall be met with a heat recovery ventilation system with minimum sensible heat recovery efficiency of 0.85. To qualify to claim this credit,the building permit drawings shall specify the option being selected and shall specify the maximum tested building air leakage and shall show the heat recovery ventilation system 3 HIGH EFFICIENCY HVAC EQUIPMENT 3a: 1.0 Gas,propane or oil-fired furnace with minimum AFUE of 94%,or Gas,propane or oiled-fired boiler with minimum AFUE of 92% To qualify to claim this credit,the building permit drawings shall specify the option being selected and shall specify the heating equipment type and the minimum equipment efficiency. 3b HIGH EFFICIENCY HVAC EQUIPMENT 3b: 1.0 Air-source heat pump with minimum HSPF of 9.0 To qualify to claim this credit,the building permit drawings shall specify the option being selected and shall specify the heating equipment type and the minimum equipment efficiency. 3c HIGH EFFICIENCY HVAC EQUIPMENT 3c: 1. Closed-loop ground source heat pump;with a minimum COP of 3.3 or Open loop water source heat pump with a maximum pumping hydraulic head of 150 feet and minimum COP of 3.6 To qualify to claim this credit,the building permit drawings shall specify the option being selected and shall specify the heating equipment type and the minimum equipment efficiency. 3d HIGH EFFICIENCY HVAC EQUIPMENT 3d: 1.0 Ductless Split System Heat Pumps,Zonal Control:In homes where the primary space heating system is zonal electric heating,a ductless heat pump system shall be installed and provide heating to the largest zone of the housing unit. To qualify to claim this credit,the building permit drawings shall specify the option being selected and shall specify the heating equipment type and the minimum equipment efficiency. 4 HIGH EFFICIENCY HVAC DISTRIBUTION SYSTEM: 1.0 All heating and cooling system components installed inside the conditioned space. This includes all equipment and distribution system components such as forced air ducts,hydronic piping,hydronic floor heating loop,convectors and radiators.All combustion equipment shall be direct vent or sealed combustion. For forced air ducts:A maximum of 10 linear feet of return ducts and 5 linear feet of supply ducts may be located outside the conditioned space.All metallic ducts located outside the conditioned space must have both transverse and longitudinal joints sealed with mastic.If flex ducts are used,they cannot contain splices.Flex duct connections must be made with nylon straps and installed using a plastic strapping tensioning tool. Ducts located outside the conditioned space must be insulated to a minimum of R-8. Locating system components in conditioned crawl spaces is not permitted under this option. Electric resistance heat and ductless heat pumps are not permitted under this option. Direct combustion heating equipment with AFUE less than 80%is not permitted under this option. To qualify to claim this credit,the building permit drawings shall specify the option being selected and shall specify the heating equipment type and shall show the location of the heating and cooling equipment and all the ductwork. 6 OPT N DESCRIPTION CREDIT(S) 5 a EFFICIENT WATER HEATING 5a: 0.5 All showerhead and kitchen sink faucets installed in the house shall be rated at 1.75 GPM or less.All other lavatory faucets shall be rated at 1.0 GPM or less.` To qualify to claim this credit,the building permit drawings shall specify the option being selected and shall specify the maximum flow rates for all showerheads,kitchen sink faucets,and other lavatory faucets. 5b EFFICIENT WATER HEATING 5b: 1.0 Water heating system shall include one of the following: Gas,propane or oil water heater with a minimum EF of 0.74 or Water heater heated by ground source heat pump meeting the requirements of Option 3c. or For R-2 occupancy,a central heat pump water heater with an EF greater than 2.0 that would supply DHW to all the units through a central water loop insulated with R-8 minimum pipe insulation. To qualify to claim this credit,the building permit drawings shall specify the option being selected and shall specify the water heater equipment type and the minimum equipment efficiency. Sc EFFICIENT WATER HEATING 5c: 1.5 Water heating system shall include one of the following: Gas,propane or oil water heater with a minimum EF of 0.91 or Solar water heating supplementing a minimum standard water heater.Solar water heating will provide a rated minimum savings of 85 therms or 2000 kWh based on the Solar Rating and Certification Corporation(SRCC)Annual Performance of OG-300 Certified Solar Water Heating Systems or Electric heat pump water heater with a minimum EF of 2.0 and meeting the standards of NEEA's Northern Climate Specifications for Heat Pump Water Heaters To qualify to claim this credit,the building permit drawings shall specify the option being selected and shall specify the water heater equipment type and the minimum equipment efficiency and,for solar water heating systems,the calculation of the minimum energy savings. 5d EFFICIENT WATER HEATING Sd: 0.5 A drain water heat recovery unit(s)shall be installed,which captures waste water heat from all the showers,and has a minimum efficiency of 40%if installed for equal flow or a minimum efficiency of 52%if installed for unequal flow.Such units shall be rated in accordance CSA B55.1 and be so labeled. To qualify to claim this credit,the building permit drawings shall include a plumbing diagram that specified the drain water heat recovery units and the plumbing layout needed to install it and labels or other documentation shall be provided that demonstrates that the unit complies with the standard. 6 RENEWABLE ELECTRIC ENERGY: 0.5 For each 1200 kWh of electrical generation per each housing unit provided annually by on-site wind or solar equipment a 0.5 credit shall be allowed,up to 3 credits. Generation shall be calculated as follows: For solar electric systems,the design shall be demonstrated to meet this requirement using the National Renewable Energy Laboratory calculator PVWATTs. Documentation noting solar access shall be included on the plans. For wind generation projects designs shall document annual power generation based on the following factors:The wind turbine power curve;average annual wind speed at the site;frequency distribution of the wind speed at the site and height of the tower. To qualify to claim this credit,the building permit drawings shall specify the option being selected and shall show the photovoltaic or wind turbine equipment type, Provide documentation of solar and wind access,and include a calculation of the minimum annual energy power production. a.Projects using this option may not use Option la,lb or lc. b.Projects may only include credit from one space heating option,3a,3b,3c or 3d.When a housing unit has two pieces of equipment(Le.,two furnaces)both must meet the standard to receive the credit. c.Plumbing Fixtures Flow Ratings.Low flow plumbing fixtures(water closets and urinals)and fittings(faucets and showerheads)shall comply with the following requirements: 1.Residential bathroom lavatory sink faucets:Maximum flow rate-3.8 L/min(1.0 gal/min)when tested in accordance with ASME A112.18.1/CSA B125.1. 2.Residential kitchen faucets:Maximum flow rate-6.6 L/min(1.75 gal/min)when tested in accordance with ASME A112.18.1/CSA B125.1. 3.Residential showerheads:Maximum flow rate-6.6 Umin(1.75 gal/min)when tested in accordance with ASME A112.18.1/CSA B125.1 7 Prescriptive Energy Code Compliance for All Climate Zones in Washington Project Information r� Contact Information e. This project will use the requirements of the Prescriptive Path below and incorporate the the minimum values listed.In addition,based on the size of the structure,the appropriate number of additional credits are checked as chosen by the permit applicant. Authorized Representative Date All Climate Zones R-Valuea U-Factora Fenestration U-Factor' n/a 0.30 Skylight U-Factor n/a 0.50 Glazed Fenestration SHGCb•e n/a n/a Ceiling, 49i 0.026 Wood Frame Wallg,m,n 21 int 0.056 Mass Wall R-Value' 21/21h 0.056 Floor 309 0.029 Below Grade Wall" 10/15121 int+TB 0.042 Slab R-Value &Depth 10, 2 ft n/a *Table R402.1.1 and Table R402.1.3 Footnotes included on Page 2. Each dwelling unit in a residential building shall comply with sufficient options from Table R406.2 so as to achieve the following minimum number of credits: 1. Small Dwelling Unit: 1.5 credits Dwelling units less than 1500 square feet in conditioned floor area with less than 300 square feet of fenestration area. Additions to existing building that are greater than 500 square feet of heated floor area but less than 1500 square feet. �. Medium Dwelling Unit: 3.5 credits All dwelling units that are not included in#1 or#3.Exception: Dwelling units serving R-2 occupancies shall require 2.5 credits. C3. Large Dwelling Unit: 4.5 credits Dwelling units exceeding 5000 square feet of conditioned floor area. Additions less than 500 square feet: .5 credits Table R406.2 Summary Option Description Credit(s) 1 a Efficient Building Envelope 1 a 0.5 0.5 1 b Efficient Building Envelope lb 1.0 1c Efficient Building Envelope 1c 2.0 2a Air Leakage Control and Efficient Ventilation 2a 0.5 2b Air Leakage Control and Efficient Ventilation 2b 1.0 2c Air Leakage Control and Efficient Ventilation 2c 1.5 3a High Efficiency HVAC 3a 1.0 1.0 3b High Efficiency HVAC 3b 1.0 3c High Efficiency HVAC 3c 1.5 3d High Efficiency HVAC 3d 1.0 4 High Efficiency HVAC Distribution System 1.0 5a Efficient Water Heating 5a 0.5 o. S 5b Efficient Water Heating 5b 1.0 5c Efficient Water Heating 5c 1.5 1.5 5d Efficient Water Heating 5d 0.5 6 Renewable Electric Energy 0.5 *1200 kwh 0.0 Total Credits 3.50 *Please refer to Table R406.2 for complete option descriptions Window Schedule & Glazing Area CE© 1570 Ply_Gem U-Factor.30 Front Elevation Area 1 3050 15 1 3050 15 1 3050 15 1 4040 16 1 6040 24 Right Side Elevation Rear Elevation 1 3036 10.8 1 3036 10.8 1 6068 40.8 1 5040 20 1 5040 20 Left Side Elevation Totals 10 187.4 Wall Square Footage 1200 Walls minus Windows 983.2 Simple Heating System Size: Washington State This heating system sizing calculator is based on the Prescriptive Reauirements of the 2015 Washington State Energy Code(WSECI and ACCA Manuals J and S.This calculator will calculate heating loads only.ACCA procedures for sizing coolina systems should be used to determine cooling loads. The glazing(window)and door portion of this calculator assumes the installed glazing and door products have an area weighted average U- factor of 0.30. The incorporated insulation requirements are the minimum prescriptive amounts specified by the 2015 WSEC. Please fill out all of the green drop-downs and boxes that are applicable to your project.As you make selections in the drop-downs for each section,some values will be calculated for you.If you do not see the selection you need in the drop-down options,please call the WSU Energy Extension Program at(360)956-2042 for assistance. Project Information Contact Information 111 E Westlake Way Joe Cedarland Allyn 253-208-8136 Heating System Type: •All OtterSysterns QHeat R"'p To see detailed instructions for each section,place your cursor on the word"Instructions" Design Temperature instructions v - - - Design Temperature Difference(AT) 47 Shelton AT=Indoor(70 degrees)-Outdoor Design Temp Area of Building Conditioned Floor Area Instructions Conditioned Floor Area(sq ft) F 1,57( Average Ceiling Height Conditioned Volume - Average Ceiling Height(ft) 8.0 12,560 Glazing and Doors U-Factor X Area = UA 0.30 187 56.22 Skylights U-Factor X Area = UA 0.50 - Insulation Attic U-Factor X Area = UA R-49 0.026 17570 40.82 Single Rafter or Joist Vaulted Ceilings U-Factor X Area UA No Vaulted Ceilin s in thi — 0 Above Grade Walls(See Figure i) U-Factor X Area UA �4 R-21 Intermediate 0.056 983 55.06 Floors U-Factor X Area UA R-38 0.025 r 1,570 39.25 Below Grade Walls(see Figurer) U-Factor X Area UA No Below Grade Walls in t --- 0 -" Slab Below Grade(see Figure 1) F-Factor X Length UA No Slab Below Grade in t — Slab on Grade(Sae Figure 1) F-Factor X Length UA ` No Slab on Grade in this — 0 Location of Ducts Unconditioned Space Duct Leakage Coefficient 1.10 Sum of UA 191.35 Envelope Heat Load 8,993 Btu/Hour Figure 1. Sumof UAXAT Air Leakage Heat Load 6,375 Btu/Hour �.�`�\_ Voiume X 0.6 X AT X.018 r Above I Building Design Heat Load 15,369 Btu/Hour Air Leakage+Envelope Heat Loss Building and Duct Heat Load 16,906 Btu/Hour Duds in unconditioned space:Sum of Building Heat Loss X 1.10 Ducts in conditioned space:Sum of Building Heat Loss X 1 Maximum Heat Equipment Output 23,668 Btu/Hour Building and Duct Heat Loss X 1.40 for Forced Air Furnace Building and Duct Heat Loss X 1.25 for Heat Pump (07101113) t-!!y--02V) 7 a0C� S/ MASON COUNTY RESIDENTIAL PLANS SUBMITTAL CHECKLIST Owner's Name: r 0 Jor7 Id -qM +- Date:? 7 I Project description: Documents: 1570 YYZ— B U ' L D' N G RECEIVED wilding Permit Application Completed. JUL 0 l 2017 Mechanical/Plumbing Application Completed. lanning Intake Checklist Completed. 615 W. Alder Street Site plan includes: Allowable building area, roof overhangs, decks, etc. Fire Apparatus &Access Road info required? Yes ✓Stormwater Checklist Completed. Energy Code Application Form - O Electric wall heater O Electric central furnace �pe O Heat pump with electric furnace O Heat pump with LPG furnace O Boiler ea ) O Ductless Heat Pump O Other: Specify: Construction Plans: _✓3 Sets (2 full size sets w/engineered calculation & 1 reduced sized set 11X17 min.(no calculation needed ) r/Plans Legible j/Recognized Scale v Elevation Views Cross Section P# Z Foundation Plan _Roof Framing Plan ✓ Floor Plan -Use of rooms labeled (all floors) Floor Framing Plan -all floor levels including loft, crawlspace, etc. Deck Framing Plan including r�covered porch, carports -/)cF �~- eofch : COr cre*E Plan Details: �rµde- L� $X i 2 BAtk, �Jb - Zocip ja3+s e�aoG _Roof framing details, truss lay-out may be needed (Hip and girder location shown) Wall Framing - Does bearing-wall height exceed 19,? (Engineering may be required) —Floor framing: Floor joists (size &spacing): Floor beams: - Window headers. Typical header: 4-1 m a Garage header: i,o x t Z _ Foundation: footing size, reinforcement _Concrete Walls- Does Concrete Wall Height Exceed 8'? (Engineering may be required, see details) y- Landings at all exits? Less than 30" above grade?Q N (must be shown on site plan) --'Water Heater. Location: ra Type: ✓Heated By Furnace- Location of Fu ace Fuel type: I Fireplace/Stove Information Shown -Fuel Type? Location(s): Window Sizes Marked on Plans. Braced wall panels (shear walls) MUST be marked/indicated on plans. fkj�L L i 4 Engineered No Snow load: Seismic: D2 Design Code: 2-0 15 Are plans stamped (,A-> Manufactured Homes: 0 '4 Floor Plans (rooms &areas must be labeled) Foundation Type: ANSI/Manufacture mfnd/or d Engineered footing/founda on Bas ent Decks*: __�4x4 min. ngs required each entrance (m st be shown on site/plot p n) "Cove d decks an decks reat than a 4'x that exceed 30', from rade red es a permit and constru6tion olari. COMMENTS: \J Intake review(initia ): ✓ Date: H:\permit tech building checklist2015.doc Revised 8.5.2016 If any of the items listed below are either indicated or missing within the construction documents; the plans must be engineered or returned to the applicant for resolution. ENGINEERING REQUIRED: Braced wall panels/brace wall lines are not marked on plans (R602.10) Amount and location of bracing does not meet minimum required in Table R602.10.1 DESIGN CRITERIA: All notes and details required as a result of the engineered analysis shall be transferred onto proposed building plans. Wind 85 MPH, Exposure B (unless proven otherwise). Seismic Zone: D2, Snow psf. IRREGULAR BUILDINGS R301.2.2.2.5 Irregular portions of structures shall be designed in accordance with accepted engineering practice. A portion of a building shall be considered to be irregular when one or more of the following conditions occur: 1) Exterior shear wall or braced wall line are not in one plane vertically from the foundation to the uppermost story in which they are required. See exceptions. 2) Roof or floor is not laterally supported by shear walls or brace walls lines on all edges. 3) Portion of roof or floor extend more than 6 ft. beyond the braced wall line. 4) End of BWP extends more than 1 ft. over an opening more than 8 ft in width below. 5) Opening in a floor or roof exceed the lesser of 12 ft. or 50% of the least floor or roof dimension. 6) Portions of floor level are offset vertically 7) Shear wall lines do not occur in two perpendicular directions. 8) If a story above grade includes masonry or concrete construction*When this applies the entire story shall be designed. In accordance with accepted engineering practice. *(exception: fireplaces, chimneys, and veneer as permitted by the code). ***Applicant must take plans to a design professional to address items indicated above*** Notes/Comments for design professional: H:\permit tech building checklist2015.doc Revised 8.5.2016 w w Name Parcel# `04o1-I-1WVl��J -I BLD# � s Mason County BUILDING Department of Community Development Small Parcel Stormwater Management Application/Worksheet (page 2 of 2) Based Upon the information you have provided a Stormwater Site Plan IS Required for this development activity. Title 14,Chapter 14.48 of the Mason County Code(MCC)regulates compliance requirements for Stormwater Management in this jurisdiction.A complete copy of the ordinance can be found on the Mason County website: bqRL/www.co.mason.wa—us/code/commissioners/index.htm Please follow the links to"Title 14,Chapter 14.48 Stormwater Management". Regulated activities shall be conducted only after Mason County Public Works approves a stormwater site plan (Mason County Code Title 14 Chapter 14.48 section 14.48.70).You will receive a copy of the Public Works document entitled"Managing Storm Drainage on Small Lots,The Small Parcel Stormwater Site Plan".This document will assist you in preparing the necessary information and plans for Public Works to review and approve. Per Department of Public Works this document will constitute an approved plan if all of the relevant details* are to be installed in their entirety AND no part of the stormwater system adversely affects any septic system(see Environmental Health information below). If an alternative system is to be used a plan will need to be submitted to Public Works for approval. A design by a registered professional may be required for more complex sites. *These details are found in the document Managing Storm Drainage on Small Lots, The Small Parcel Stormwater Site Plan on the pages that begin with"Handout" PLEASE INITIAL BELOW TO INDICATE THE STORMWATER MANAGEMENT PLAN FOR THIS SITE A) The relevant details from Managing Storm Drainage on Small Lots, The Small Parcel Stormwater Site Plan will be installed in th it entirety AND the system will be located as not to adversely affect any septic systems on this,or any other,parcel. B) An alternative plan and/or professional design will be submitted to the Department of Public Works for approval AND the system will be located as not to adversely affect any septic systems on this,or any other,parcel. If you have further questions pertaining to parcel drainage and stormwater management Mason County's Public Works Department can provide additional instructions,guidance and examples.(Section 14.48.130)contact Public works at: Phone:(360)-427-9670 EXT.450 Mail:P 0 Box 1850,Shelton WA 98584 Physical:415 N 6th St,Shelton WA 98584 If this development has,or will have,a septic/drainfield system you may need to contact Mason County Division of Environmental Health to ensure that the stormwater system will not adversely affect the septic system of this,or any other,parcel.You may also wish to consult with the septic design professional involved with the project.Mason County Division of Environmental Health can be reached at: Phone:(360)-427-9670 EXT.352 Mail:P 0 Box 1666, Shelton WA 98584 Physical:426 W Cedar St,Shelton WA 98584 A condition will be added to the building permit that states,in part,that all conditions the stormwater site plan will be met prior to a request for final inspection of the building permit. Owner/Builder/Agent Acknowledges that submission of inaccurate information may result in a stop work order or permit revocation. Acknowledgement of such is by signature below.I declare that I am the owner,owner's legal representative,or the contractor.I further acknowledge that the information provided is accura employees of Mason County are granted access to the above- described property for review and i ctio y b quired. X wner gent/Contractor(circle one)Date: Page 2 of 2 '1 Name _-lJHRU"0 Parcel# W)9 )3 ( BLD# 1::OFZsr R:_:71C__ouPc.(s Mason County Department of Community Development Small Parcel Stormwater Management Application/Worksheet (page 1 of 2) Per Mason County Code,Title 14,Chapter 14.48 a stormwater site plan is required whenever a building application is made for residential development,or redevelopment',with more than 2,000 square feet of impervious surface 2. 'Redevelopment means,on an already developed site,the creation or addition of impervious surfaces,structural development including construction,installation or expansion of a building or other structure,and/or replacement of impervious surface that is not part of a routine maintenance activity,and land disturbing activities associated with structural or impervious redevelopment. 2Common impervious surfaces include,but are not limited to,rooftops,walkways,patios,driveways,parking lots or storage areas, concrete or asphalt paving,gravel roads,packed earthen materials,and oiled,macadam or other surfaces which similarly impede the natural infiltration of stormwater.Open,uncovered retention/detention facilities shall not be considered as impervious surfaces. To Calculate Impervious Surfaces Please Complete This Table Surface Type Length X Width = I Area *All dimensions in feet Buildings X = IIS70 X = Measurements for buildings are taken at the ElEl X _ perimeter of the farthest projections (example: eaves/gutters) X = Driveways X X = Length of drive begins at the right of way X = Parking Areas X = X = Any paved, gravel or packed area per definition above table X = Patios/Walks X = X = Any paved, gravel or packed area per definition above table X = Others X X = If the total impervious area of the proposed site X = development is greater than 2000 square feet a Small Parcel Stormwater Site Plan is Required Total Impervious Surface Area(sum of all areas) If the Total Impervious Surface Area is LESS THAN 2000 Square Feet,please read,acknowledge and sign below. Based Upon the information you have provided a Stormwater Site Plan IS NOT required for this development activity. Owner/Builder/Agent Acknowledges that submission of inaccurate information may result in a stop work order or permit revocation. Acknowledgement of such is by signature below.I declare that I am the owner,owner's legal representative,or the contractor.I further acknowledge that the information provided is accurate and employees of Mason County are granted access to the above- described property for review and inspection as may be required. X Owner/Agent/Contractor(circle one)Date: If the Total Impervious Surface Area is GREATER THAN 2000 Square Feet, please read,acknowledge and sign the information provided on page 2 of 2. Page I of 2 ,ENVIRONMENTAL P 7 0�&5-. 7 HEALTH -L BASIS OF BEARING: ASSUMED NORTH ALONG THE CENTERLINE OF J U L O 7 2011 WESTLAKE WAY LEGAL DESCRIPTION: LOT 34 IN LAKELAND VILLAGE NO. 7, 615 W. Alder Street ! �/ AS RECORDED IN VOLUME 9 OF PLATS PAGES 155-157. ASSESSORS PARCEL N0. 12219-50-00034 A III E WESTLAKE WAY ALLYN, WA. 98524 Q� --SCALE: 1"=50 FEET 0 25 50 100 f APPROVED Flow MC PUBLIC HEALT �, � 1 OOT AUG 0 4 2017 BUIFLDING SETBACK ALP TYPICAL �' f has � LOT 34 I GARAGE 00 f >_ I and LAKQ 6 ,d d.l► r o o F � Wait r r�� J cr Z CL CURVE TABLE -- --\�`� 20 Q R L c I Cl 23'40'30" 150.00 61.96 C2 37'00'00" 150.00 96.87 LEGEND C3 43'46'00" 130.00 99.30 Le I PLAT MONUMENT SITE PLAN MAP AGATE LAND SURVEYING, PLLC 61F W SH? PROFESSIONAL LAND SURVEYOR P� U FOR 2680 E. AGATE RD. - P.O. BOX 246 _ 0a CEDARLAND FOREST RESOURCES LC S14a-TON, WA 98584 - (360) 426-4172 o IN THE DRAWN BY DATE:06/31/2017 JOB NO.- 3954 zers� a`y SE1/4 SE1/4 BECK t`ss R�..ISTEg v4 SCALE. 1 INCH = 50' EET 1 OF 1 fOA'AL LA�� SEC 19, T22N, R1 W, W.M, CHECK® BY SG8 LE NO. 3954_CFR.DWG you U - v iS o ��Cwed ir\ -rlj_5�f�a'cK (- e e o�erhqA� PLANNING ornn-r-11 far) BASIS OF BEARING: AMMs��WAY JUL THE CENTOWNE OF JUL 0 7 2017 LEGAL DESCRIPHON: ��5 W. Alder Street LOT 34 IN LAKELAND VILLAGE NO. 7, AS RECORDED IN VOLUME 9 OF PLATS PAGES 155-157. -`n-� ASSESSORS PARCEL NO. 12219-50-00034 III E NESTLAKE WAY ALLYN, WA. 98524 Q� SCALE: 1"=50 FEET 0 25 50 100 AL.: ORM FLOW 5 FOOT BUILDING SETBACK ♦ t TYPICAL / / APPROVE LOT 34 J§IASON COUNTY DCD P ANNING oo(A `&t `�� } Q j 1:: SITE PLAN REQUIRED TO B ON E ITE ss _ �3 t , CHANGES SUBJECT TO AP RO AL sev e e Date 7 2 (,�II G� L.G�K21��cL d�llo,�.i �� •`� o I �'O'`' Way CURVE TABLE -- �`� 0.1 Q R L I Cl 23'40'30" 150.00 61.96 C2 37'00'00" 150.00 96.87 LEGEND C3 43'46'00" 130.00 99.30 PLAT MONUMENT SITE PLAN MAP AGATE LAND SURVEYING, PLLC C' By SX7' PROFMONAL LAND SURWM q�? of yI4r FOR 2680 E. AGATE 0. - P.O. BOX 246 ° 0AM9 FOREST RESUIRCES LLC srlELTu+, WA 9a5B4- (360)426-4172 o IN THE DRAWN BY DATE. 06/31/2017 JOB No: 3954 SE114 SE114 c�S,s.R�ISTERr"� � BECK SCALE: i INCH = 50' :1 OF 1 A'AL LATi9 �`/ CHECKED BY SEC 19, T22N, R1�; U. SGB LE NO. 3954_CFR.DWG U i S a �Cwe d ►� MASON COUNTY � rp Shelton (360) 427-9670 DEPARTMENT OF COMMUNITY DEVELOPMENT Belfair (360) 275-4467 Planning Mason County Bldg.1 411 N.5th Elma (360) 482-5269 P.O.Box 279 Shelton,WA 98584 1d54 n V�TA71PT) 1XJUREQUEST FOR REFUND APR 11 2012 DATE OF REQUEST: 0S' \ Zo1 MASON CO. PLANNING DEPT. NAME: MAILING ADDRESS:p() box 31� 4 p CITY, STATE: UDC' ZIP: 2 C7 PHONE: �LIC�(GI �5y�� Email: 0Ca510 O'A 21ia' omr';, CD 0-7 The applicant does hereby request a refund on receipt number: 12 O 120 y000-.�00.�(11-7 Dated: 23 Mcu-�2012 Permit No. Issued for$ 255."`' �7 Reason for Refund Request: 0,pQ c4 c7 n G.-S 5U 4o Y ki V"--j r o- tnsP=gC�ior-, NQ1 (JC%ra c-ar-W tZZI9 n Inu:U,r'� Or_C-zj:)'6.. iDQ—V\CtitiQ- 51 IXC: 0_ 0--c oO SIGNA STATE AUDITOR REQUIREMENTS You must enclose the original receipt with this request. If a Building Permit was issued the request for refund will cancel this permit. Include all documents,including issued permit with this request. BUILDING DEPARTMENT REQUIREMENTS The International Building Code authorizes refunding of any fee erroneously paid or collected when no work has been done under a permit issued in accordance with this code. Refund amount for permit fees may be authorized at no more than 80%of permit fee. Refund for plan review fees is authorized(at no more than 80%of plan review)when application is withdrawn or canceled before plan review is done. No refunds shall be authorized for refund requests more than 180 days after initial fee was paid. PLANNING DEPARTMENT POLICY Fees may not be refiuided once a permit is issued,after a public hearing is advertised,or after processing has been complete. No more than 80%may be refunded if no work has been completed. After a determination of completeness/incompleteness,no more than 50%may be refunded. A minimum of$20.00 shall be withheld for administrative costs. Should the required application be submitted in error of DCD staff,a 100%refund shall be made. / - lam b�oN .`oar MASON COUNTY COMMUNITY SERVICES / n PERMIT ASSISTANCE CENTER: Permit No: UJZ' L5� •BUILDING*PLANNING•PUBLIC HEALTH.FIRE MARSHAL s 615 W.Alder Street,Shelton,WA 98584 Phone Shelton:(360)427-9670 ext. 352•Fax:(360)427-7798 Phone © [r d E D s Belfair(360)275-4467•Phone Elma:(360)482-5269 RECEIVE V 1854 BUILDING PERMIT APPLICATION JUL 0 7 2017 BUILDING 615 W. Alder Street PROPERTY OWNER INFORMATION: CONTRACTOR INFORMATION: NAME a- AI24 NAME: Vn-mE MAILING ADDRESS: LIU MAILING ADDRESS: CITY STATE: ZIP:% CITY: STATE: ZIP: PHONE#I: - PHONE: CELL: PHONE#2: EMAIL : EMAIL:In @,&d(if I&&remTsmz,Com L&I REG# EXP. / /-u CONTACT PERSON : OWNER�4 CONTRACTOR ❑ OTHER❑ NAMEt,bEE��I,l ( � MAILING ADDRESS:�S"Q R5 CWK-:lz CITY: STATE: ZIP: PHONE: CELL: EMAIL: PARCEL INFORMATION: Pr I n U6-A PARCEL NUMBER(12 Digit Number) I a, a 1 J ',--5,000034 ZONING R-I P LEGAL DESCRIPTION(Abbreviated) ( .3 FIRE DISTRICT SITE ADDRESS I ( I • k1r�1 L CITY DIRECTIONS TO SITE ADDRESS IS THE PROJECT WITHIN 300 FT OF SLOPE(S)GREATER THAN 14%: YES❑ NO❑ IS PROPERTY WITHIN 200 FT: (Check all that apply): SALTWATER❑ LAKE❑ RIVER/CREEK❑ POND❑ WETLAND❑ SEASONAL RUNOFF ❑ STREAM❑ TYPE OF WORK: NEW X ADDITION ❑ ALjT—E�R-AT((ION Ei]t� REPAIR❑ OTHER ❑ �p USE OF STRUCTURE(Residence,Garage,Commercial Bldg,Etc.) Res IO�I pl�— IS USE: PRIMARY �, SEASONAL❑ NUMBER OF BEDROOMS__ NUMBER OF BATHROOMS HEATED STRUCTU 7 YES(Whole Bldg) ❑. YESI/(Part[s]of Bldg) ❑ ` 'NO❑ DESCRIBE WORK NS GE 1571 U � a� i N U�L' �1 1 l ' ' �� (Valuation/Project Bid Amount:$ ) SQUARE FOOTAGE: IST FLOOR 1 5,U sq.ft. 2ND FLOOR sq.ft. 3RD FLOOR sq.ft. BASEMENT sq.ft. DECK sq.ft. COVERED DECK I Ll sq.ft. STORAGE sq.ft. OTHER sq.ft. GARAGE �sq.ft. Attached Y Detached❑ CARPORT sq.ft. Attached❑ Detached❑ MANUFACTURED HOME INFORMATION: *4 COPIES OF THE FLOOR PLAN REQUIRED* MAKE MODEL YEAR LENGTH TH BEDROOMS B SERI OWNER acknowledges that submission of inaccurate information may result in a stop work order or permit revocation. Acknowledgement of such is by signature below. I declare that I am the owner and I further declare that I am entitled to receive this permit and to do the work as proposed. I have obtained permission from all the necessary parties, including any easement holder or parties of interest regarding this project. The owner or legal representative, represents that the information provided is accurate and grants employees of Mason County access to the above described property and structure(s)for review and inspection. This permit/application becomes null &void if work or authorized construction is not commenced within 180 days or if construction work is suspended for a period of 180 days. PROOF OF CONTINUATION OF WORK ON THIS PERMIT IS BY MEANS OF INSPECTION. INACTIVITY OF THIS PERMIT APPLICATION OF 180 DAYS OF MOREMILL CAUSE THE APPLICATION TO BE EXPIRED. (MASON UNTY CODE 14.08.42) X Z",-�01 ZZ�Z nature of OWNER(Must be signed by the OWNER) / Date DEPARTMENTAL REVIEW APPROVED DATE DENIED DATE TAGS/NOTES/CONDITIONS BUILDING DEPARTMENT q (( PLANNING DEPARTMENT FIRE MARSHAL PUBLIC HEALTH �Pso� co" MASON COUNTY COMMUNITY SERVICES Permit No: PERMIT ASSISTANCE CENTER: •BUILDING •PLANNING •FIRE MARSHAL 615 W.Alder St- Shelton, WA 98584 R����VED www.co.mason.wa.us txsr Phone Shelton:(360)427-9670 ext. 352• Fax:(360)427-7798 Phone Belfair:(360)275-4467• Phone E/ma:(360)482-5269 JUL 0 7 2LId B U I L D I NAIMBING & MECHANICAL PERMIT APPLICATION 615 W. Alder Street OWNER INFORMATION: CONTRACTOR INFORMATION: NAMECMn2JJ NAME: MAILING ADDRESS: MAILING ADDRESS: CITY- STATE: ZIP: CITY: STATE: ZIP: IS`PHONE: — PHONE: CELL: 2n,PHONE: EMAIL : EMAIL: &I REG — I'J EXP. / /Jj PARCEL INFORMATION: I n PARCEL NUMBER(12 Digit Number): Zoning: r LEGAL DESCRIP ION Abb eviated): ' SITE ADDRESS: CITY: DIR,ETIONS TO SITE ADDRESS: LC_T_ TYPE OF JOB: �r NEW X ADD ALT REPAIR OTHER USE OF BUILDING LOC IO R OF FIXTURES/UNITS— IST FLOO 2NDFLOOR BASEMENT GARAGE OTHER PLUMBING FIXTURES(SHOW NUMBER OF EACH) MECHANICAL UNITS Type of Fixture No.of Fixtures Fees Fuel Type:Electric LPG Natural Gas Ductless_ Toilets Type of Unit No.of Units Fees Bathroom Sink _ Furnace Bath Tubs Heat Pump Showers Spot Vent Fan Water Heater Propane Tank Clothes Washer Gas Outlets Kitchen Sinks Wood/Gas/Pellet Stove Dishwasher � Kitchen Exhaust Hood Hose bibs Dryer Vent Other Solar Panel Other Base Fee Base Fee TOTAL PLUMBING TOTAL MECHANICAL OWNER acknowledge submission of inaccurate information may result in a stop work order or permit revocation.Acknowledgement of such is by signature below. I declare that I am the owner,owners legal representative,or contractor. I further declare that I am entitled to receive this permit and to do the work as proposed. I have obtained permission from all the necessary parties,including any easement holder or parties of interest regarding this project.The owner or authorized agent represents that the information provided is accurate and grants employees of Mason County access to the above described property and structure(s)for review and inspection.This permit/application becomes null&void if work or authorized construction is not commenced within 180 days or if construction work is suspended for a period of 180 days.PROOF OF CONTINUATION OFTHIS PERMIT IS BY MEANS OF INSPECTION.INACTIVITY OF THIS PERMIT APPLICATION OF 180 DAYS WILL INVALIDATE THE APPLICATIO X Sign re of Owne a e DEPARTMENTAL REVIEW APPROVED DATE DENIED DATE TAGS/NOTES/CONDITIONS BUILDING DEPARTMENT PLANNING DEPARTMENT FIRE MARSHAL Visit us on-line: http://www.co.mason.wa.us/community_dev/ Rev:1/27/2016 JBN